Flareless Tube Presetting Tool

ST878D, Tool Kit, Flareless Tube Presetting, This tool is used in conjunction with a G85 lockbolt gun in order to preset BACSS13AP flareless coupling sleeves and MS21922 fittings. Presetting tools provide a more accurate and positive leak-proof method of coupling flareless compression fittings. Presetting the sleeve on the tubing prior to.

Kenwood kvt-614 firmware update. • • • • • • • • • • • • 2018 • • KMM-BT522HD • • KDC-X702 • KDC-BT772HD • • KDC-X7200DAB • • KMR-D772BT • KDC-X5200BTM • KDC-X5200BT • KDC-X502 • KDC-BT572U • • DPX793BH • • KDC-BT720DAB • DPX-7100BT?

Use a deburring tool to remove burrs from the NOTE: A flareless-tube connector may be inside and outside of tube. Remove filings, chips, and used as a presetting tool in case of an grit from inside the tube. Clean the tube. Select the emergency. However, when connectors are proper size die blocks, and place one-half of the die used as presetting tools, aluminum connectors block into the flaring tool body with the countersunk should be used only once, and steel end towards the ram guide. Install the nut and sleeve, connectors should not be used more than five and lay the tube in the die block with 1/2 inch times.

• Mode of Operation: Models CA-3000, CA-3200: Automatic and Manual Timing Models CM-3000, CM-3200: Manual Timing Inhalation, Exhalation, Pause Times: CA-3000, CA-3200: Automatic mode, 0 to 5 seconds CM-3000, CM-3200: User variable “Off” Position: Yes - connects to ambient Blower Type. Cough assist respironics mask. • O N T R O L S C O N N E C T O R S SECTION 4 & V I S U A L I N D I C AT O R S C A - 3 0 0 0, C A - 3 2 0 0 R O N T A N E L 1. • C M - 3 0 0 0, C M - 3 2 0 0 R O N T A N E L O N T R O L S Pressure: Varies the inhalation and exhalation pressures together (also see Inhale Pressure).

Protruding beyond countersunk end. Place the other half of the die block into the tool body, close latch plate, and tighten the clamp nuts fingertight. Insert the upset flare punch in the tool body with the gauge end toward the die blocks. The upset flare punch has one end counterbored or to gauge the amount of tubing needed to form a double lap flare. Insert the ram and tap lightly with a hammer or mallet until the upset flare punch contacts the die blocks, and the die blocks are set against the stop plate on the bottom. Use a wrench to tighten the latch alternately, beginning with the closed side, to prevent distortion of the tool. Reverse the upset flare punch; insert the upset flare punch and ram into the tool body.

Tap lightly with a hammer or mallet until the upset flare punch contacts the die blocks. Remove the upset flare punch and ram. Insert the finishing flare punch and ram. Tap the ram lightly until a good seat is formed (fig. Check the seat at intervals during the finishing operation to avoid overseating. Special procedures are used in the presetting operation.

Select the correct size presetting tool or a flareless fitting body. Clamp the presetting tool or flareless fitting body in a vise. Slide a nut and then a sleeve onto the tube, and make sure the pilot and cutting edge of the sleeve points toward the end of tube. Select the lubricant from table 6-4, and lubricate fitting threads, tool seat, and shoulder sleeve.

Place the tube end firmly against the bottom of the presetting tool seat, while slowly screwing the nut onto the tool threads with a wrench until the tube Flareless Fitting Preparing tube ends for flareless fitting requires a presetting operation whereby the sleeve is set onto the tubing. Presetting is necessary to form the seal between the sleeve and the tube without damaging the connector.